Electrical Trade
Electrician’s Tools You Can Rely On
Professional tools need to perform in everyday work: during the first use, after many work steps and under changing conditions. GEDORE stands for tools designed for controlled work, reliable performance and a long service life.
For electricians, this means a clear selection for typical applications, durable tools for daily use and solutions that can be integrated into existing equipment. Good tools do more than save effort. They also reduce rework, make repetitive tasks easier and support consistent results. That is exactly what matters in professional electrical work.
Cutting and Stripping Cables Cleanly
Clean cut surfaces and undamaged conductor insulation are the foundation of a reliable installation. With the right cable cutters and wire strippers, you can work in a controlled and efficient manner—even when many cables need to be prepared one after another.
When choosing your tools, pay attention to the intended conductor cross-section, good visibility of the work area and handling that suits your daily applications.
Processing Ferrules and Cable Lugs Safely
When crimping, a reproducible connection and controlled force transmission are essential. A suitable crimping tool helps you process ferrules and cable lugs cleanly and standardise your work processes.
Choose the tool to match the connector, conductor cross-section and specific crimping application. This helps you avoid unnecessary rework and achieve consistent results.
Tightening Connections and Terminals Precisely
Loose or incorrectly tightened connections can cause problems in electrical installations. For applications that require a defined tightening torque, torque screwdrivers or other controlled tools are suitable.
Especially in control cabinet construction and repetitive assembly tasks, a clearly defined work process helps to maintain consistent quality.
Work Safely with VDE Tools
When working on electrical systems, the appropriate qualification is just as important as suitable tools. VDE-tested or correspondingly marked tools are designed for specific electrical applications and support safe work within their intended area of use.
Before starting any work, check the system, observe the applicable safety regulations and use the tool only as intended. VDE tools do not replace isolation, testing or personal protective equipment.
When Limited Space Requires Maximum Precision
Control cabinets, junction boxes and installation areas often provide very little room to move. Long handles or unwieldy tools can make the work more difficult and increase the risk of slipping or touching adjacent components.
Compact pliers, slim screwdrivers and well-coordinated tool solutions help you work in confined areas with control. Good accessibility, a secure grip and a clear view of the connection are essential.
Slim designs and controlled force transmission are particularly useful when working in control cabinets. They allow you to reach terminals and screw connections without requiring unnecessary space. In customer service, every gram matters and every tool needs to be quickly accessible. A carefully selected set of equipment reduces search times and helps you carry out typical repair and installation tasks with less equipment.
Your Basic Equipment for Everyday Electrical Work
Electricians work with pliers, screwdrivers and cutting tools every day. Ergonomic handles, balanced geometry and smooth-running mechanisms can help reduce strain on the hand and make repetitive movements more comfortable.
This is particularly important when cutting cables, stripping wires or working on connections for many hours. A good tool should not only feel right during the first use—it should also support you after many work steps.
The following features matter in ergonomic electrician’s tools:
- secure, non-slip grip
- smooth-running mechanism
- balanced weight distribution
- good visibility of the work area
- suitable size for the application
- low effort for repetitive tasks
From “A” for Assembly to “W” for Wiring
The tools you need in your equipment depend on your area of work. For many electrical tasks, the following categories provide a useful foundation:
Cutting and Stripping
- Side cutters: VDE side cutters, 160 mm, VDE 8314-160 H—for cutting work with VDE sleeve insulation up to 1,000 V in accordance with EN 60900/IEC 60900.
- Cable cutters and wire strippers: VDE stripping side cutters, 160 mm, VDE 8315-160 H—combining cutting and stripping functions, with stripping holes for solid and stranded conductors with cross-sections of 1.5 mm² and 2.5 mm².
- Cable knife: Universal cable knife 8094—the specific model and design should be selected according to the cable type.
Gripping and Holding
- Combination pliers: VDE combination pliers with 2-component handle, 200 mm, R29300200—with gripping zones for flat and round materials, a long induction-hardened cutting edge and a 2-component handle.
- Long-nose pliers: Electronics long-nose pliers, 140 mm, 8307-3—with slim jaws angled at 45°, opening spring and ESD design for more delicate gripping work.
- Flat-nose pliers: VDE flat-nose pliers with dip insulation, 160 mm, VDE 8120-160—with long, serrated gripping surfaces and VDE insulation up to 1,000 V.
- Water pump pliers: VDE water pump pliers, 10 inches, 7-position adjustment, R29100010—with longitudinally serrated gripping surfaces, seven adjustment positions and VDE insulation up to 1,000 V.
Screwing and Assembly
- VDE slotted screwdriver: VDE slotted screwdriver VDE 2170—available with several blade widths from 2.5 to 8 mm.
- VDE Phillips and Pozidriv screwdrivers: VDE screwdriver set VDE 2170/2160 PH/PZ 077—a suitable GEDORE VDE set solution for slotted, PH and PZ screw profiles.
- VDE torque screwdriver: GEDORE torque screwdriver for defined tightening torques where these are specified or required for the respective connection.
Connecting and Organising
- Crimping pliers: Various models from 8155 to 8157 for insulated connectors or cable lugs.
- Tool bag or tool case: GEDORE L-BOXX 136 with electrician’s assortment, 36 pieces—a compact assortment solution for mobile use.
Ready for Your Next Assignment with GEDORE?
Find the right GEDORE tools for your daily tasks in the electrical trade—precise, robust and designed for professional applications.
Answers to the Most Frequently Asked Questions
Depending on the area of work, basic equipment includes side cutters, combination and long-nose pliers, wire strippers, cable cutters, VDE screwdrivers and a suitable crimping tool. A torque screwdriver can also be useful for defined screw connections.
VDE tools are designed for electrical work in accordance with the applicable testing and marking requirements. Not every tool with a handle that looks insulated is automatically suitable for working on electrical systems. Look for clear labelling and use the tool only as intended.
This depends on the cable type, material and cross-section. A suitable pair of side cutters may be sufficient for thin conductors. For larger cross-sections or special cables, you should use a cable cutter designed for the application. The manufacturer’s specifications are decisive.
Use a wire-stripping tool suitable for the cable and conductor cross-section. Set the cutting or stripping function correctly and work with controlled movements. Damaged conductors should not simply continue to be used; they should be assessed professionally and replaced if necessary.
A suitable crimping tool is useful when ferrules need to be processed reproducibly and according to the intended application. The tool, ferrule and conductor cross-section must be compatible.
A torque screwdriver allows you to maintain defined tightening torques where this is specified for the respective connection. This supports consistent assembly quality and can help prevent connections from being too loose or overtightened.
Focus on the tasks that occur most frequently. A compact selection of cutting, stripping, gripping and screwdriving tools often provides the foundation. Add specialist tools only when they are regularly required for your assignments.
VDE tools are not a general authorisation to work on live equipment. Work on electrical systems may only be carried out by appropriately qualified persons and in compliance with the applicable safety regulations. Before use, the system, tool and working method must be checked.
